Snorkel

A snorkel - is it worth it.


After years of searching for a snorkel, I finally agreed to buy an old one from Grahame. My other option was to adapt pone from a LandRover defender (Nigel had done that very well).

It is not a snorkel

First lesson is that it is not a snorkel. It is a raised air intake. The crucial difference is a snorkel is expected to be waterproof, but this design is open in the vehicle wing, which is not sealed, it has drain holes. So if left standing in very deep water, then the engine would suck in water not air.

A raised air intake is supposed to be good for drawing in air with less sand and dust.

But the key feature is that it looks cool.

Fitting is Difficult

It is a large plastic item, that stretches across two steel body panels. The fixings points don't line up well. It is prone to vibration and so the mounts need to be flexible. To keep water out it needs to be fitted tight and various holes sealed up. And the indicator light needs to fit on the outside.



Parts are needed

It is not a simple bolt on. Holes for the existing exterior trim do not line up for the snorkel. It needs several special parts and they are no longer all available. It needs a foam strip c 10mmx3mm.  (I used 6mm thick, which was not ideal). Some holes need to be covered if a waterproof snorkel is wanted. I needed an extra mounting point near the indicator to seal the gap between snorkel and body.


Parts list

Iveco 2003/2-14911111 | 30-8 NEW DAILY (96) | 554000 6406274
  
ITM   PART N.  QT DESCRIPTION             NOTE
001    4193370 02 PIPE  
              This is a simple beak valve. The pipe itself is part of the main snorkel. The part number is for the rubber valve only.
002    9060048 02 SILENTBLOCK  
             Critical item out of stock. It is a "cotton reel" rubber mount. The thickness is critical. Too thick and you will not be able to tighten the snorkel against the wing. Too narrow and it will not tighten up without bending the wing. I used 25mm diameter 10mm thick. The studs were 12mm
003   14560187 02 CABLE STRAP             L=178 MM  
           It is a jubilee clip
004   16750121 01 HEXAGON NUT             M6  
005   17143604 03 SCREW  
006   93929804 01 CONNECTING PLATE  
          This is a metal plate that goes on the outside of the snorkel. The indicator light push fits into it. 
007   93930043 04 SCREW  
008   93933538 01 HOUSING  
          This is the same part with or without a snorkel. Mine had a loose rubber seal at the outboard edge. It has a drain slot at the bottom, which needs to be sealed for any pretence of being water tight.
009   93936820 01 AIR PIPE/DUCT           RIGHT 
           This is the main plastic snorkel. Only one part number, but there are at least two distinct versions with One, or Two drain pipes clearly visible. They are complicated pieces with various baffles and holes.
010   93936826 01 PROTECTIVE GRILLE  
        Critical part, only available as a pack of 5, but easily made.
011   93936819 01 CONNECTING PLATE  
         Critical part not available. It is needed to fix the snorkel to the wing. It matches up the hole in the wing with the cotton reel mount on the snorkel. Depending on the thickness of the cotton reel rubber, it may need to be an offset bracket. I used a flat piece of steel.

All installed. Looks cool

Indicator fitted

The connecting plate in position

Cotton reel mount. The thickness is critical

Thisis the normal 2WD duct it has a slot open to the wing cavity. It needs sealing up for any pretence of being waterproof.

Cotton reel mount in place

Second cotton reel mount. Showing some of the snorkel detail



Comments

  1. we have the snorkel.
    please visit my website
    https://www.suonama.com.cn

    ReplyDelete

Post a Comment

Popular posts from this blog

Fuel tank

Alternator upgrade

Cold Start system Thermostarter